- Sturdy ¼ λ mobile antenna in professional industry standard quality.
- Factory-adjusted broad-band matching unit for 74.2 - 87.5 MHz (optimized for 74.21 - 77.66 MHz and 84.01 - 87.46 MHz).
- Tuning not necessary – but can be fine-tuned if needed.
- Separate broadband matching unit for time-saving mounting.
- Necessary cable length between the matching unit and the antenna mount: 100 mm (FME junction cable included).
- Stainless steel Z-mount with socket joint and wing screw.
- Simple mounting exclusively with access from the outside.
- FME antenna cable for 80 MHz BOS can be mounted directly in the matching unit without special antenna connectors.
Descripción
Especificaciones
| Eléctrico ES | ||
|---|---|---|
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
| Mecánico ES | ||
|---|---|---|
|
||
|
||
|
||
|
||
|
||
Designaciones de pedido
| Modelo | Producto No. | |
|---|---|---|
| ML 1-ZR/BOS1 BBMU | 130000628 |
Additional Data
SUNDRIES : For connection of special cables (RG 213, H2000, RG 223 etc.) to the matching unit the jumper cable JPC 40/RG 58/FN can be used. This is a 40 cm long RG 58 cable with one FME connector and one N-female connector.
Installation (if mounted from the outside)
-
Equip the matching unit with FME antenna cables and the supplied 100 mm junction cable.
-
Draw the 100 mm junction cable through the antenna hole from the outside (e.g. with a drawstring between the car roof and the dome).
-
The Z-mount is particularly well suited for mounting on car-roofs because of its ability to be installed exclusively with access from the outside. The Z-Mount for roof thickness from 2 mm to 7.5 mm must be mounted from the inside. However, the antenna can be installed anywhere on the car, as the Z-mount is equally well suited for mounting on e.g. trunk or wing.
-
Attach the cable to the Z-mount and install the mount from the outside following the below given instructions.
1. Installation Dimension
Additional Data
SUNDRIES: For connection of special cables (RG 213, H2000, RG 223 etc.) to the matching unit the jumper cable JPC 40/RG 58/FN can be used. This is a 40 cm long RG 58 cable with one FME connector and one N-female connector.
INSTALLATION (if mounted from the outside)
-
Equip the matching unit with FME antenna cables and the supplied 100 mm junction cable.
-
Draw the 100 mm junction cable through the antenna hole from the outside (e.g. with a drawstring between the car roof and the dome).
-
The Z-mount is particularly well suited for mounting on car-roofs because of its ability to be installed exclusively with access from the outside. The Z-Mount for roof thickness from 2 mm to 7.5 mm must be mounted from the inside. However, the antenna can be installed anywhere on the car, as the Z-mount is equally well suited for mounting on e.g. trunk or wing.
-
Attach the cable to the Z-mount and install the mount from the outside following the below given instructions.
1. INSTALLATION DIMENSIONS
2. INSTALLATION STEPS
Do not use sealer on rubber gasket or other places.
3. TUNING
The ML 1-ZR/BOS1 BBMU is factory-tuned to the following 80 MHz BOS area:
LOW: 74.215 - 77.655 MHz
HIGH: 84.015 - 87.455 MHz
Fine-tuning or frequency change can if needed be done as follows:
Adjustment of the BBMU BOS1 by means of SWR 4000
- Tune the SWR in on the desired centre frequency and suitable spacing (for instance 30 MHz).
- Adjust C1 till the SWR curve emerges on the display.
- Adjust C2 till the best possible SWR minimum is reached on the required frequency.
- Fine-tune the SWR minimum and the bandwidth step by step means of C1 and C2.
SWR 4000 Analyzer with built-in signal generator and graphic display range of measurement 30 - 2700 MHz.
3.Tuning
The ML 1-ZR/BOS1 BBMU is factory-tuned to the following 80 MHz BOS area:
LOW: 74.215 - 77.655 MHz
HIGH: 84.015 - 87.455 MHz
Fine-tuning or frequency change can if needed be done as follows:
Adjustment of the BBMU BOS1
- Tune the VSWR in on the desired centre frequency and suitable spacing (for instance 30 MHz).
- Adjust C1 till the VSWR curve emerges on the display.
- Adjust C2 till the best possible VSWR minimum is reached on the required frequency.
- Fine-tune the VSWR minimum and the bandwidth step by step means of C1 and C2.
Z-Mount
Productos relacionados
Combiners compactos
View all Amphenol Procom hybrid Tx/Rx Compact combiners for VHF & UHF. To be used e.g. in mobile TETRA/PMR/LMR control stations. Learn more.
Antenas de combinación GPS
Amphenol Procom have a huge assortment of GPS Antennas. Beneficial products for navigation/location applications. Read more here.
Bajo perfil / encubierto
In our collection of Low Profile Antennas covering VHF and UHF bands with omnidirectional coverage. Best quality products on the market. View our collection.
Triplexers
RF Multiplex Filters portfolio by Amphenol Procom consist of quality Triplex Filters and Quadroplex Filters with high performance. Learn more here.