XG-Combi Mount

GPS mount for GPS Antennas and Other Frequencies

Description

  • Mobile mount with a nice, “streamline”-look, which can be installed everywhere on the car in an 19 mm dia. hole.
  • Especially suited for mounting on the narrow strip on rear wing between trunk lid and car side.
  • M6 thread whip-mounting system.
  • Very low requirements to installation depth both under and after installation.
  • Designed for installation with access from the outside only.
  • Bendable section in mount makes whip tiltable 30° by hand.
  • Complete line of whips available for all communications bands up to 1300 MHz.
  • Mounting body made of stainless steel !
  • Choice between two connection principles:
    • XG-Combi mount: FME-connection and GPS (supplied without cable).
    • XGP4-Combi mount: Permanently attached 4 m RG 58 cable terminated with FME-connector and GPS.
  • GPS-antenna for fixed installations.
    • Full hemispherical coverage.
    • Built-in high-gain, low-noise amplifier.
    • Right-Hand Circular Polarization (RHCP).
    • 2.85 V - 5 V supply voltage (typical 3 V).

Spécifications

Électrique FR
Modèle XG-COMBI MOUNT
Application Mount for mobile antennas
Mécanique FR
Profondeur Intégrée Active : 30 mm
Passive : 11 mm
Connexion(s) Cable: RG 178, length 150 mm Connector: FME-male
Matériaux Black-chromed brass
Weather- and shockproof plastics
Stainless steel
Couple D'Installation 4 +/- 1 Nm
Couleur Noir
Dimensions 48 mm x 28 mm (LxW)
Whip Connection M6 filetage
Poids XG-version: Approx. 60 g
XGP4-version: Approx. 200 g
Montage 19 mm de diamètre trou
Épaisseur De Plaque De Montage Max. 2 mm
Antenne GPS
Bruit De Bruit (Amplificateur GPS) < 1.5 dB (typical 1.1 dB)
Gain (Amplificateur GPS) 22 dB -2 dB
Fréquence (GPS) 1575.42 +/-1.023 MHz
Alimentation (GPS) DC 2.85 V ~ 5 V (typical 3 V)
Consommation Actuelle (Amplificateur GPS) <20 mA
Impedance (GPS) 50 Ω

Désignations de commande

Model N ° de produit Description
XG-COMBI MOUNT 130002032 XG-Combi mount with FME-system
XGP4-COMBI MOUNT 130002043 XGP4-Combi mount with 4 m RG 58 cable and FME-connector
1 m FME(f) to FME(f) cable 130000437
2 m FME(f) to FME(f) cable 130000447
3 m FME(f) to FME(f) cable 130000457
4 m FME(f) to FME(f) cable 130000466
5 m FME(f) to FME(f) cable 130000474
6 m FME(f) to FME(f) cable 130000483
4 m FME(f) to FME(f) cable, white 110000064
6 m FME(f) to FME(f) cable, white 110000066
12 m FME(f) to FME(f) cable, white 110000068
18 m FME(f) to FME(f) cable, white 110000069
FME(f)-FME(f) Connector Adaptor 130000583
FME(m)-P(m) (Prolongation) Connector Adaptor 130000565
FME(m)-N(m) Connector Adaptor 130000571
FME(m)-SMA(f) Connector Adaptor 130000578
FME(m)-BNC(m) Connector Adaptor 130000566
FME(m)-TNC(m) Connector Adaptor 130000569
FME(m)-UHF(m) Connector Adaptor 130000572
FME(m)-MiniUHF(m) Connector Adaptor 130000573
FME(m)-MiniUHF(m)(Elbow) Connector Adaptor 130000582
FME(m)-BNC(m)(Elbow) Connector Adaptor 130000580
FME(m)-TNC(m)(Elbow) Connector Adaptor 130000581
FME(m)-SMA(m) Connector Adaptor 130000577

Additional Data

ACCESSOIRES FME

CABLE FME
REF. LONGUEUR
1 m FME 1 m
2 m FME 2 m
3 m FME 3 m
4 m FME 4 m
5 m FME 5 m
6 m FME 6 m
4 m FME-white 4 m white
6 m FME-white 6 m white
12 m FME-white 12 m white
18 m FME-white 18 m white
CONNECTEURS FME
REF. CONNECTEURS
FME-FME FME-FME
FME-P Prolongation
FME-N N
FME-FSMA FSMA
FME-BNC BNC
FME-TNC TNC
FME-UHF UHF
FME-MUHF Mini-UHF
FME-EMUHF Elbow-MUHF
FME-EBNC Elbow-BNC
FME-ETNC Elbow-TNC
FME-SMA SMA

 

For further information about other types of FME-cables and FME-connectors, please compare the cable and connector data sheets under accessories in our catalogue.


INSTALLATION

XG-Combi mount antenna types can be mounted anywhere on the car, however, roof top mounting is always recommended.

The oblong XG-Combi mount is able to be mounted on the often very narrow strip on the rear wing between the trunk lid and the side of the car.

Mounting can take place with access from the outside or inside when drilling an 19 mm dia. hole.

A good contact surface on the inside of the car body must always be ensured, thus enabling the base plate to get in direct contact with the metal parts of the car, which is of utmost importance for proper performance of the antenna.

When cleaning the car in car-washing machines, the whip is easily removed using a fork spanner, size 9 mm. The whip is refitted again by screwing it onto the thread stud and tightening it lightly with the spanner.

As the XG-Combi mount is internally equipped with a bendable section, the antennas can always be adjusted to an upright position independent of the tilt angle of the installation spot (up to 30° tilt).

 

1. INSTALLATION DIMENSIONS

 

2. INSTALLATION STEPS


Do not use sealer on rubber gasket or other places.

 

ASSEMBLY INSTRUCTIONS

  • Put GPS-FME-connector-cable through the gasket (2).
  • Put the gasket (2) + GPS-part (1) over the body (B).
  • Put the body (B) + gasket (3) + GPS-part (1) through the ø19 mm hole.
  • Put the housing (4) over the body (B) and be sure that the GPS-part (1) fits into the square hole in the body (B).
  • Put the threaded part over the body (B) and tighten max. 4 ±1 Nm!
  • Put the corrugated plastic unit (6) over the body (B).
  • Mount the antenna whip se figure 4.

 


A SELECTION OF THE VARIOUS WHIPS WHICH CAN BE CONNECTED TO THE XG-COMBI MOUNT